This proceedure is a "tried and true" method. Unlike some rec.pyro postings, which are informational, or just plain speculative, this proceedure WORKS. I have used it myself to make my own supply of perchlorate - until I decided to quit because I was making it far too fast to use.
This proceedure works well to make chlorates as well. The proceedure can be modified easily to make only chlorates. When using this proceedure to make perchlorate, it produces significant amounts of chlorate as a by-product. This is because carbon rods are not highly efficient in converting chlorate to perchlorate. Other anodes work better, but this proceedure was designed using easily available common materials and supplies. --- Author
Get some carbon rods from the welding shop. They are made by "arcair", and are 3/8" diameter by 12" long, and cost between 40 to 60 cents(US) each. They are copper plated, and they are used for a welding proceedure known as "gouging".
Cut off the top of a plastic 1 gallon milk jug. This is a good cheap source of containers for using in this proceedure.
Dissolve 1/2 cup of salt in 2 liters of warm water. Put this in a small plastic container. Cut out a piece of coffee can, roughly 4" by 4" with a tab extending up to connect a wire to. The dimensions are not critical. With a 6 volt battery charger, connect the minus (-) connector to the piece of coffee can. Wrap some aluminum foil on the end of the carbon rod, to improve the electrical connection, and connect the plus (+) connector of the charger to it.
Turn on the charger, and let it run for about 20 minutes. The copper will be removed from the rod. If some still remains, run it for a little longer till it is free of copper.
Discard the salt water used to remove the copper.
You can probably use a 12V charger, but the current may get too high, so you may need to reduce how much of the rod is being etched at one time.
Make a mixture of salt and potassium chloride solutions. Dissolve roughly 2 ounces (60 grams) of salt, and 8 ounces (240 grams) of potassium chloride in 2 liters (just a bit more than 2 quarts) of hot water. There is much room for inaccuracy here, because the exact mixture is not absolutely critical.
At this point, it is good to add between 2 to 10 grams of either potassium chromate or dichromate. While this is not absolutely necessary, it helps improve how much perchlorate is finally produced. The process will work without it, but not quite as well.
NOTE: Potassium chloride can be obtained as several commonly available products, such as: dietary salt substitute, ice melter (look at label for actual contents), and "muriate of potash" from farm and garden supply shops. Hagenow Laboratories carries potassium dichromate.
The reason a mixture of salt and KCl is used, is two fold. First, salt is more easily electrolyzed than KCl, but after it converts to chlorate (and perchlorate), it will tend form the potassium salt instead of the sodium salt. The electrolysis tends to work on the sodium salt, while the final potassium perchlorate forms, and due to it's poor solubility, tends to crystalize out of solution. Secondly, the concentration of KCl is chosen to help prevent chlorate from crystalizing out, while being too high for the perchlorate to remain in solution, which causes it to crystalize out as it is created. These concentrations may be varied, to compensate for different operating temperatures. It was designed to operate at 40C, and will work fine above that temp, but below it, you might get some chlorate crysatlizing out, in which case you might need to reduce the amount of KCl just a little.
I have been using a little salt in my mixture, but someone could exclusively electrolyze KCl, without the addition of salt. The purpose of the salt is to provide a sodium salt which is more easily electrolyzed than the potassium salt. It is NOT necessary, and will probably work well with only KCl. ****** (Chlorate note) ******
BTW, chlorates are produced here as an intermediate chemical product. Chlorates tend to be the predominant component around 1 1/2 to 2 days of operation. Chlorate could be caused to crystalize out during electrolysis if the concentration of KCl in the starting electrolyte solution is increased to nearly saturation (about 21 ounces KCl/ with 2 ounces of salt). Although I have not concentrated on chlorate production, I would expect that you could actually run it for more than 2 days - possibly up to 4 or 5 days, and keep building up a layer of largely chlorate crystals on the bottom. In that case, I would _GUESS_ that you could get around 2 pounds of chlorate after 5 days of operation.
NOTE: A setup with the electrodes running electricity through an electrolyte is called a "Cell". This setup is commonly refered to as a cell throughout this description.
Let the liquid electrolyze for about 5 days continuously. Add water to make up for water lost during the process, and try to keep it roughly constant.
A couple times a day, you will need to check the current level, and adjust the rod position to keep the current in the 8-12amp range. Mine has been running between 40 - 50C, but commercial proceedures keep the temp just below 40C to reduce carbon rod errosion. The rods will gradually errode away, but if you use a 6V charger, one rod will probably last for the full 5 days.
You can also use higher voltage chargers, but you will probably need to connect several electrolytic cells together to keep the voltage accross ONE cell to be about 6 volts. If you use a 12 V charger, you will need 2 cells ( 12V/(6V per cell) = 2cells). If you connect more than 1 cell in series, you may need to use a voltmeter to check the actual voltage accross each cell - because it will change depending upon the resistance differences between the cells, which can be adjusted by re-positioning the rods.
The purpose for the U shaped trough cathode (-) electrode, is to cause the gas bubbles formed to generate a convection flow up through the trough. This causes the chemical products produced at each electrode to mix and react efficiently. Other electrode geometries will work, some better, and others worse. The key is to cause the two electrodes to be very close to each other, and cause the chemical products to mix well to help form chlorate and perchlorates. The WORST case situation is where the electrodes are on opposite sides of the cell, causing the chlorine gas produced at the anode (+) to tend to bubble and escape out of solution into the air.
The potassium perchlorate crystalizes out as it electrolyzes. When you're done, you have a mixture of black carbon, perchlorate, and some chlorate after you drain off the liquid. I generally get a layer of perchlorate crystals about 1 inch (2.5cm) thick on the bottom, which tends to be about 1 pound.
Cool the liquid in a freezer to help increase the amount of perchlorate that is crystalized out, before draining the electrolyte liquid. When draining the electrolyte, save it if you want to re-electrolyze it to make even more perchlorate again.
Load the crystals into a filter, and use boiling water to dissolve the perchlorate out. As it filters, the perchlorate forms nice flat rhombic shaped (almost square) flakes that float out of solution. You watch it as it cools, and watch for chlorate crystals, which tend to look like clusters of cactus needles. When they start to form (well after the perchlorate has largely crystalized out), you drain the liquid, and add some room temp water which is to be about 2 - 3 times the volume of the crystals you have in the container. Shake them, and let it stand overnight to dissolve any chlorate crystals. Then drain, wash (with ice cold water), and dry the crystals.
NOTE: Coffee filters generally aren't good enough to filter out the black carbon particles. You can load a coffee filter with a good layer of diatomaceous earth, and then use it to filter the liquid. Diatomaceous earth is used to filter swimming pool water, and a 10 pound bag can be obtained for less than US$10.00.
You can purify them again by weighing the dried crystals, and adding enough water to dissolve the whole mass as if it was pure chlorate (i.e. 7g/100ml water)*. Use hot water, and then cool it down to room temp. You might even need to cool get the perchlorate to begin to crystalize (it seems to super saturate commonly). You might be able to get it started by adding a small amount of perchlorate dust as crystal seeds - if you have some to start with.. Then wash your crystals (with ICE COLD water), and dry them. That will help produce a higher purity product of perchlorate. If you want to make a chlorate-free batch of perchlorate, repeat this process again. It will be essentailly free of chlorate if you double crystalize it, and make certain you wash the crystals several times with cold water.
Example: 100 grams of crystals would require 100grams/(7gm/100ml) = 14.3 (100 ml), or 1430 ml of water, or about 48 ounces.
NOTE: When harvesting the crystals, a cotton cloth makes a good filter. I wear rubber gloves, and squeeze the excess liquid from the crystals before & during washing them. Squeezing helps remove additional contaminants which are dissolved in the liquid that wouldn't otherwise be removed by simple gravity filtering. While this method loses very small crystaline particles, the loss tends to be very small in comparison to the amount of crystals harvested.
Perchlorate is very easy to make, but it takes a little work. The hardest ingredient to get is patience.
This proceedure generates small amounts of chlorine gas, as well as hydrogen gas. It should be conducted outdoors, or in a well ventilated building which is NOT used for living quarters! Hydrogen can accumulate in non-ventilated and sealed rooms to form potentially explosive mixtures with air!! Chlorine generally is more of a irritant, but can be poisonous at high concentrations. There are also other (?) chlorine oxides and/or ozone produced which should also be avoided.
Chlorates and perchlorates are NOT chemicals for playing!! They are serious oxidizing agents which can be used to make VERY DANGEROUS pyrotechnic mixtures - _ESPECIALLY CHLORATES_ !!! Be certain to read up on all litterature describing the use and dangers of these compounds! It is VERY EASY to forget the safety hazards associated with these oxidizers in a time of haste - and lose a limb or your life as a result of your forgetfulness! Be careful to clean up any oxidizer which is spilled on carpets, or solutions which have spilled or splashed on any form of flamable material, including clothes, wood, paper, etc.
CHLORATES ARE ESPECIALLY FRICTION AND SHOCK SENSITIVE! PERCHLORATES CAN ALSO PRESENT THE SAME HAZARDS, BUT NOT AS BADLY AS CHLORATES!
ALSO, AVOID THE DISASTEROUS MIXTURE OF CHLORATE WITH SULFUR. NEVER MIX EITHER OF THESE WITH ANY FORM OF PHOSPHORUS, AS IT CAN IGNITE OR EXPLODE BY THE FRICTION OF SIMPLY MIXING THEM!!!!!
Also, chlorates must be kept from any form of acids, especially sulfuric. Even small traces of acids (from the presence of sulfur, etc) can cause what "appeared" to be a stable mixture, to ignite at some unknown time later!